Abdellatif AliAutomatisierung · Embedded · SoftwareAutomation · Embedded · Software

Breitband-Vivaldi-Antenne – von der FDTD-Simulation zum Gerber-ExportBroadband Vivaldi antenna – from FDTD simulation to Gerber export

Entwurf einer planaren, koplanar gespeisten Tapered-Slot-Antenne auf FR4 ab 850 MHz: parametrisches Modell in openEMS/GNU Octave, systematische Fehlersuche im Solver-Setup, Parameteroptimierung und ein fertigungsvorbereitetes KiCad-Layout.Design of a planar, CPW-fed tapered-slot antenna on FR4 from 850 MHz: parametric model in openEMS/GNU Octave, systematic debugging of the solver setup, parameter optimisation and a manufacturing-ready KiCad layout.

RolleRoleEigener Entwurf & BerichtOwn design & report
KontextContextStudienprojekt, 5 ECTS · Prof. Dr.-Ing. J. PassokeStudy project, 5 ECTS · Prof. Dr.-Ing. J. Passoke
StackopenEMS · Octave · KiCad
StatusAbgeschlossen & eingereichtCompleted & submitted
01ZielObjective

Möglichst breitbandig, möglichst klein, auf Standard-FR4As wideband as possible, as small as possible, on standard FR4

Aufgabe war eine planare Vivaldi-Antenne mit unterer Grenzfrequenz 850 MHz auf FR4 (1 mm, εr = 4,3, tan δ = 0,023) mit 50-Ω-SMA-Anschluss – simuliert mit openEMS unter Octave und als Gerber-Datensatz für die Fertigung am Fachgebiet aufbereitet.The task: a planar Vivaldi antenna with a lower cut-off of 850 MHz on FR4 (1 mm, εr = 4.3, tan δ = 0.023) with a 50 Ω SMA connector – simulated with openEMS under Octave and prepared as a Gerber dataset for fabrication at the department.

−13,05 dBS11 bei 852,6 MHz (1. Resonanz)S11 at 852.6 MHz (1st resonance)
Simulation, feines NetzSimulation, fine mesh
3,32 dBiDirektivität bei 852,6 MHzDirectivity at 852.6 MHz
Simulation
87,0 %StrahlungswirkungsgradRadiation efficiency
Simulation
50,7 − j23,0 ΩEingangsimpedanz bei 850 MHzInput impedance at 850 MHz
aus Portdatenfrom port data
02ModellModel

Exponentielles Taper-Profil mit CPW-SpeisungExponential taper with CPW feed

Die Massekontur folgt y(x) = C₁·e^(Rx) + C₂ zwischen Throat (y₀) und Apertur (yₐ). Gespeist wird über eine koplanare Leitung, die am Taper-Übergang in den Schlitzleitungsmodus einkoppelt. Alle Abmessungen sind Parameter des Octave-Skripts – Grundlage für die automatisierte Optimierung.The ground contour follows y(x) = C₁·e^(Rx) + C₂ between throat (y₀) and aperture (yₐ). A coplanar waveguide feeds the structure and couples into the slot-line mode at the taper transition. Every dimension is a parameter of the Octave script – the basis for automated optimisation.

ParameterParameterFinaler WertFinal value
Platine (L × B)Board (L × W)275 × 160 mm
Taper-Länge LTaper length L240 mm
Apertur yₐ / Throat y₀Aperture yₐ / throat y₀60 mm / 1,9 mm
Taper-Rate RTaper rate R0,023 /mm
CPW: Leiterbreite / SpaltCPW: width / gap3,0 mm / 0,4 mm
SubstratFR4, 1 mm, εr 4,3, tan δ 0,023
02bFrequenz-ExplorerFrequency explorer

Wie groß ist die Antenne im Verhältnis zur Wellenlänge?How large is the antenna relative to the wavelength?

Die Platine ist maßstäblich aus den finalen Designparametern gezeichnet. Wählen Sie eine Frequenz: Wellenlänge und Aperturverhältnis werden exakt berechnet, der S11-Status stammt aus den dokumentierten Simulationsergebnissen. Wellenfronten und Strahlungskeule sind eine stilisierte Erklärung, kein Simulationsergebnis.The board is drawn to scale from the final design parameters. Pick a frequency: wavelength and aperture ratio are computed exactly, and the S11 status comes from the documented simulation results. Wavefronts and lobe are a stylised explanation, not a simulation output.

f =f = 852 MHzS11-Bänder: ProjektdatenS11 bands: project data Wellen: IllustrationWaves: illustration
Wellenlänge λWavelength λ–
Apertur 2·yₐ = 120 mmAperture 2·yₐ = 120 mm–
S11 (Simulation)S11 (simulation)–
Nächste ResonanzNearest resonance–

Einordnung: Bei 850 MHz ist die Apertur nur ≈ 0,34 λ breit – eine Faustregel nennt ≈ λ/2 für gute Anpassung an der unteren Grenzfrequenz. Das erklärt, warum die simulierte Anpassung nur in schmalen Bändern (829–876 MHz, 1255–1324 MHz) unter −10 dB liegt.Context: at 850 MHz the aperture is only ≈ 0.34 λ wide – a rule of thumb calls for ≈ λ/2 for good matching at the lower cut-off. This helps explain why the simulated match stays below −10 dB only in narrow bands (829–876 MHz, 1255–1324 MHz).

03FehlersucheDebugging

Drei numerische Probleme, systematisch gelöstThree numerical problems, solved systematically

Bevor belastbare Ergebnisse vorlagen, mussten drei voneinander unabhängige Fehler im Simulationsaufbau gefunden werden.Before results could be trusted, three independent faults in the simulation setup had to be found.

01Kurzschluss am Throat/Taper-ÜbergangShort at the throat/taper transition
SymptomSymptomS11 ≈ 0 dB über das ganze Band – Hinweis auf einen Kurzschluss statt Anpassung.S11 ≈ 0 dB across the band – a short rather than a match.
DiagnoseDiagnosisy₀ war mit 1,0 mm unabhängig von der CPW-Geometrie gesetzt; Masse und Speiseleiter überlappten an der Anregungsstelle.y₀ was fixed at 1.0 mm independent of the CPW geometry; ground and feed overlapped at the excitation point.
LösungFixy₀ = W_cpw/2 + g, damit die Massekontur stetig an den CPW-Spalt anschließt.y₀ = W_cpw/2 + g, so the ground contour joins the CPW gap continuously.
02Zeitschritt-Kollaps durch Gleitkomma-RundungTime-step collapse from floating-point rounding
SymptomSymptomFDTD-Zeitschritt ≈ 6·10⁻²⁰ s statt ≈ 10⁻¹²…10⁻¹³ s.FDTD time step ≈ 6·10⁻²⁰ s instead of ≈ 10⁻¹²…10⁻¹³ s.
DiagnoseDiagnosisZwei Netzlinien nur 4,4·10⁻¹⁶ mm auseinander – Rundungsfehler der Exponentialfunktion verletzten faktisch die Courant-Bedingung.Two mesh lines only 4.4·10⁻¹⁶ mm apart – rounding in the exponential effectively violated the Courant condition.
LösungFixNetzlinien unter 0,01 mm Abstand vor DefineRectGrid zusammengeführt.Merged mesh lines closer than 0.01 mm before DefineRectGrid.
03Rechenzeit-Explosion in der NetzglättungRun-time explosion in mesh smoothing
SymptomSymptomSmoothMesh hing bei größeren Geometrien unter Volllast.SmoothMesh hung at full CPU load on larger geometries.
DiagnoseDiagnosis60 Taper-Stützpunkte plus eng benachbarte Kanten erzeugten kombinatorischen Aufwand.60 taper samples plus closely spaced edges caused combinatorial cost.
LösungFixStützpunkte von 60 auf 10 reduziert und Kanten vorgefiltert – 25–80 s pro Lauf bei voller Konvergenz.Reduced samples from 60 to 10 and pre-filtered edges – 25–80 s per run with full convergence.
04OptimierungOptimisation

Ein Parameter pro Iteration – dann der SweepOne parameter per iteration – then the sweep

Erst die Taper-Länge (130 → 240 mm), dann die Aperturweite, schließlich ein Sweep-Skript über sechs (L, yₐ)-Kombinationen mit schnellem Explorationsnetz. Das Kriterium war der schlechteste S11-Wert im Band – nicht der tiefste Dip.First the taper length (130 → 240 mm), then the aperture width, finally a sweep script over six (L, yₐ) combinations on a fast exploration mesh. The criterion was the worst in-band S11 – not the deepest dip.

Parametersweep · ExplorationsnetzParameter sweep · exploration mesh

Orange: gewähltes Design (L = 240 mm, yₐ = 60 mm) mit dem besten Worst-Case-Wert; anschließend mit feinem Netz bestätigt. Keine Kombination erreichte S11 < −10 dB durchgängig über 850–2000 MHz.Orange: the chosen design (L = 240 mm, yₐ = 60 mm) with the best worst-case value; then confirmed on a fine mesh. No combination reached S11 < −10 dB across all of 850–2000 MHz.

05ErgebnisseResults

Was die finale Simulation zeigtWhat the final simulation shows

Resonanzen bei 852,6 MHz (−13,05 dB), 1290,5 MHz (−12,07 dB) und 1758,8 MHz (−9,39 dB). Alle Kennwerte wurden aus den Rohdaten des Simulationsports nachgerechnet.Resonances at 852.6 MHz (−13.05 dB), 1290.5 MHz (−12.07 dB) and 1758.8 MHz (−9.39 dB). All figures were recomputed from the raw port data.

Ehrliche Einordnung: S11 < −10 dB wird nur in 829–876 MHz und 1255–1324 MHz erreicht (≈ 8,5 % des Bands 850–2000 MHz). Die Antenne ist an der unteren Bandkante angepasst, aber nicht durchgängig breitbandig. Fertigung und VNA-Messung waren ein möglicher Folgeschritt und nicht Teil des Projekts.Honest assessment: S11 < −10 dB is reached only in 829–876 MHz and 1255–1324 MHz (≈ 8.5 % of the 850–2000 MHz band). The antenna is matched at the lower band edge but not continuously broadband. Fabrication and VNA measurement were a possible follow-up and not part of the project.

06KiCad

Layout direkt aus den FormelnLayout straight from the equations

  • Kupferkontur nicht nachgezeichnet, sondern aus den Taper-Formeln als SVG exportiert und 1:1 in KiCad importiert.Copper contour not traced by hand but exported from the taper equations as SVG and imported 1:1 into KiCad.
  • SMA-Edge-Launch-Footprint (Amphenol 132289), Mittelpin exakt auf dem CPW-Speisespalt.SMA edge-launch footprint (Amphenol 132289), centre pin aligned exactly with the CPW feed gap.
  • DRC: 13 Hinweise geprüft und begründet als unkritisch eingeordnet (grafischer Import ohne Netzliste, randbündige Massefläche).DRC: 13 notices reviewed and justified as non-critical (graphic import without netlist, edge-flush ground plane).
  • Gerber-X2-Export inkl. Kupfer-, Masken-, Bestückungs- und Umrisslagen sowie Excellon-Bohrdaten.Gerber X2 export incl. copper, mask, silkscreen and outline layers plus Excellon drill files.
07DokumenteDocuments

Projekt-Website, Bericht & DateienProject website, report & files